EBB 36 CAN¶

Product Profile¶

BIGTREETECH EBB36 CAN V1.0/V1.1 is a nozzle adapter board specially designed for the 36 extruder stepper motor, which is launched by the 3D printing team Shenzhen BIQU Innovation Technology Co., Ltd.. It can communicate via USB port, or CAN BUS, greatly simplifying wirings.

Features Highlights¶

With BOOT and RESET buttons reserved, users can update the firmware via DFU mode by USB.
Added protection circuit on the thermistor avoids burning the main control chip caused by leakage current from the heating rod.
User can select the thermistor’s pull-up resistors values through jumper wire, so as to support PT1000 (2.2K pull-up resistors), which makes it convenient for DIY.
Connect the USB with a jumper cap to get it power on, which effectively isolates the main control board DC-DC from USB 5V.
Reserved I2C interface allows for filament broke and clogged detection, andsupports other DIY functions.
Added anti-flyback diodes on the heating rod and fans’ ports effectively protect the MOS tube from being burned due to reverse voltage.
Anti-reverse connection protection on the power interface prevents users from burning the motherboard when mistakenly connecting the reverse power line during DIY.
Onboard MAX31865 supports selecting 2-wire or 4-wire of PT100/ PT1000.
Supports communication via CAN or USB. The terminal resistor 120R of CAN can be selected through the jumper cap, and it reserves CAN expansion interfaces.
Equipped ESD protection chip on the USB port prevents the main control board from being broken down by the static electricity of the USB port.
The adaptor board is equipped with terminals, female reeds, double-way studs and screws, which are required for DIY, greatly meeting the DIY needs of customers.

Specifications¶

External Dimensions	51.5mm x 37mm. For further details please read: Dimensions
Installation Dimensions	hole spacing 43.85mm, M3 screw hole x 2
Microprocessor	ARM Cortex-M0 STM32F072C8T6 48MHz (V1.0)
Microprocessor	ARM Cortex-M0+ STM32G0B1CBT6 64MHz (V1.1)
Input Voltage	DC12V-DC24V 6A
Logic Voltage	DC 3.3V
Heating Interface	Heating rod (E0), maximum output current: 5A
Onboard Sensor	ADXL345
Fan Interfaces	two CNC fans (FAN0, FAN1)
Maximum Output Current of Fan Interface	1A, Peak Value 1.5A
Expansion Interfaces	EndStop, I2C, Probe, RGB, PT100/PT1000, USB interface, CAN Interface
Motor Drive	Onboard TMC2209
Driver Working Mode	UART
Stepper Motor Interface	EM
Temperature Sensor Interface Optional	1 Channel 100K NTC or PT1000(TH0), 1 Channel PT100/PT1000
USB Communication Interface	USB-Type-C
DC 5V Maximum Output Current	1A

Note: BTT EEB36 CAN V1.0/V1.1 only supports Klipper at the present.

Dimensions¶

Version:V1.0

Version:V1.1

Pinout¶

Version:V1.0

Version:V1.1

Hardware Configuration¶

USB Power Supply¶

Version:V1.0

D1 RGB light will be on when the control board powers on, which shows supplying normal power. VUSB in the middle of the board is the selection terminal for power. Only when USB supplies power to the board, or the board supplies power through USB, users need to short circuit the VUSB by jump cap.

Version:V1.1

After the motherboard is powered on, the yellow-green LED1 lights will light up, indicating a normal power supply. The VUSB on the right side of the board is the power selection terminal. Only when using USB to supply power to the motherboard or need to supply power through USB, do you need to use the jumper cap to connect VUSB.

Hardware Installation¶

100K NTC or PT1000 Settings¶

Version without 31865: No need to plug a jumper cap when using a 100K NTC thermistor, and TH0's pull-up resistor value is 4.7K. When using PT1000, you need to use the jumper cap to short the two pins, as shown below picture. At this time, TH0's pull-up resistor value is 2.2K (Notice: the temperature accuracy that's read out this way will be less accurate than that of MAX31865).

Version:V1.0